|Surpassed rugged industry standards
||All Land Pride Rotary Cutters have been designed and tested and meet rigorous voluntary testing procedures according to ISO 4254-13.
||Arrives for quick and easy set-up. Minimal time wasted setting or prepping the unit.
|Rugged heavy built gearboxes
||Capable of handling heavy cutting applications
|Gearbox seal protection
||Gearbox bottom seal protection for longer bearing life.
|Sliding guard for splitter gearbox
||Sliding guard offers protection and easy access for improved efficiency of splitter
|Detachable shield on the wing gearbox
||Provides easy maintenance access to the driveline slip clutch and yoke.
|Two piece driveline shields
||Driveline grease zerks are easier to access.
|Low hitch weight on tractor drawbar
||Ideal for smaller hp tractors by reducing the amount of weight on the drawbar.
|Narrow A-frame tongue
||Allows for a tighter turning radius.
|Adjustable park jack angle
||Park jack can be adjusted to be perpendicular to the ground.
|Adjustable driveline support
||Serves as support rest for the driveline when the cutter is unhooked from the tractor.
Assist operator when attaching driveline to the tractor power take-off shaft.
|Input driveline: Cat. 6 CV
||Driveline is matched just right for tractor capacity. Constant velocity (CV) U-joint allows for 80 degree turns without doing damage to the driveline.
|Drivelines with slip-clutches:
Cat. 5 intermediate
Cat. 4 or Cat. 5 wing
|Driveline is sized right for the intended cutting capacity.
Slip-clutches will slip under load to minimize twist damage to driveline profiles.
|Grease zerks on end caps of driveline
||Intermediate and wing driveline cross journals are easier to grease.
|High blade tip speed
||Allows clean cutting of material.
|6" Blade overlap
||Eliminates skipping during turns.
|Forged blade bar (Optional)
||Provides the critical strength needed for consistent, top performance.
|3/16" Round stump jumper (Optional)
||Standard thick stump jumper material keeps damage to a minimum.
|Smooth top design
||Reduces accumulation of debris and is easier and faster to clean.
|Tops of decks are 100% welded
||Makes center and wing decks stronger.
|Deck Armor™ (Optional)
||Reduces deck damage from blade to deck contact without affecting cut quality.
|Replaceable 1/4" side skirt thickness
||Increased thickness reduces damage from objects thrown into the side skirt.
|Multiple center skid shoe locations
||Run two skid shoes under the hitch pivots or two skid shoes under the wing hinges.
|Beveled skid shoes on the wing &
|Reduces gouging the ground when turning.
|LED signal lights
||LED lights are bright, long lasting, and resist vibration, unlike incandescent lights.
|Wire harness 7-pin plug holder
||Spring hose loop mounted holder keeps wire harness plug out of the dirt and rain.
|Hinged wing section
||Allows the cutter to follow the terrain. Ideal for rough ground where hillsides, ditches,
and hollows can cause uneven cutting
|1" Solid hinge rods
||Larger diameter hinge rod provides greater strength in the hinge area.
|Wing transport lock pin
||Transport lock pin holds the wing in the folded position in the event of hydraulic loss.
|Enclosed dual 1" leveling rods
||Cutter pulls equally on the rear axle while traveling over rough terrain.
|Five-bolt hubs with larger bearings,
five lip hub seals, and bolted-on hub
|Makes the wheel assembly more durable and longer lasting. Five hub seals make it
harder for water & debris to enter the hub and grease to leave the hub. Hub caps
cannot be knocked off by foreign material.
|Drain holes in wheel rims
||Allows water to drain from wheels mounted on the folded-up wing.
Helps prevent paint deterioration and rusting to the wheel rims.
|Replaceable individual wheel spindles
||Spindles can be replaced when damaged without replacing entire axle assembly.
||Laminated tires: Eliminates flats.
Air-filled tires: Give better cushion while transporting.
Foam-filled tires: Give better cushion while transporting and can’t go flat.
|LP Performance Hitch™ (Optional)
||One person Hook-up. Great for uneven terrain, reduces drawbar wear. Hitch pivots
freely up and down and pivots about the tractor drawbar up to 12 degrees in both left
and right directions.
|Bar-Tite hitch (Optional)
||Ideal for extreme conditions. Clamps tight to drawbar eliminating drawbar wear.
|Maintenance free tongue & axle pivots
||Self lubricating journal bearings make for less maintenance.
|Color-coded hydraulic hose handles
||Easy hose identification & sturdy handle to easily connect & disconnect from tractor.
|Hydraulic hose holders
||Tongue mounted hose holder keeps hose tips out of the dirt.
|Greasable cast steel, continuous
|Cast steel hinges make a strong connection & are easy to lubricate.
|Center axle options
||HD Single suspension center axle: Spring cushion at the cylinder for cushion with
least amount of moving parts.
Independent suspension wing axles: Offers additional suspension support on the
Walking tandem center axle: Designed for versatility over a multitude of terrains.
Parallel pivot center axle: Provides unmatched ground contact for hill-like terrains.
|Wing axle option
||HD Single suspension wing axles: One piece wing axle that gets support from the
center cylinder spring cushioning on the center axle for cushioning with the least
amount of moving parts.
Independent suspension wing axle: Offers additional suspension support on the
Walking tandem wing axle: Designed for versatility over a multitude of terrains.
Parallel pivot axle: Provides unmatched ground contact for hill-like terrains.
|Dual-acting fold cylinder (Optional)
||Allows for a narrow transport width of 7'-3" (2.21 m).
||Easily change cut height with a flip of a spacer.
|SMV Mounting Socket (Standard)
SMV Sign (Accessory)
|SMV mounting socket receives most SMV signs equipped with a mounting blade for
ease of attachment and removal when transporting on a truck or trailer.
SMV sign is offered as an accessory when the tractor’s SMV sign and mounting
blade does not fit the cutter’s standard SMV mounting socket.